Frequency-hopping spread spectrum
Frequency-hopping spread spectrum (FHSS) is a method of transmitting radio signals by rapidly switching a among many frequency , using a sequence known to both and . It is used as a in the (CDMA) scheme frequency-hopping code division multiple access (FH-CDMA) .
FHSS is a wireless technology that spreads its signal over rapidly changing frequencies. Each available frequency band is divided into sub-frequencies. Signals rapidly change (“hop”) among these in a pre-determined order. Interference at a specific frequency will only affect the signal during that short interval. FHSS can, however, cause interference with adjacent (DSSS) systems. A sub-type of FHSS used in wireless data transfer is adaptive frequency hopping spread spectrum (AFH).
Contents
Spread-spectrum
<!– move this list to ? –> A spread-spectrum transmission offers three main advantages over a fixed-frequency transmission:
Military use
Spread-spectrum signals are highly resistant to deliberate , unless the adversary has knowledge of the spreading characteristics. radios use techniques to generate the channel sequence under the control of a secret (TRANSEC) that the sender and receiver share in advance.
By itself, frequency hopping provides only limited protection against eavesdropping and jamming. Most modern military frequency hopping radios also employ separate encryption devices such as the Speech Security Equipment. military radios that use frequency hopping include the JTIDS/MIDS family, the Aeronautical Mobile (OR) communications system, and the Combat Net Radio, .
Civilian use
In the US, since the (FCC) amended rules to allow frequency hopping systems in the unregulated 2.4 GHz band, many consumer devices in that band have employed various spread-spectrum modes.
Some that employ frequency-hopping spread spectrum technology have been developed for unlicensed use on the 900 MHz band. Several such radios were marketed under the name (eXRS). Despite the name’s similarity to the , the system is a proprietary design, rather than an official FCC allocated service.
Frequency-hopping spread spectrum technology is also used in some RC (radio controlled) car transmitters and receivers.
Motorola has deployed a business-banded, license-free digital radio that uses FHSS technology: the DTR series, models 410, 550 and 650.
Technical considerations
The overall bandwidth required for frequency hopping is much wider than that required to transmit the same using only one . However, because transmission occurs only on a small portion of this bandwidth at any given time, the effective interference bandwidth is really the same. While providing no extra protection against wideband , the frequency-hopping approach does reduce the degradation caused by narrowband interference sources.
One of the challenges of frequency-hopping systems is to synchronize the transmitter and receiver. One approach is to have a guarantee that the transmitter will use all the channels in a fixed period of time. The receiver can then find the transmitter by picking a random channel and listening for valid data on that channel. The transmitter’s data is identified by a special sequence of data that is unlikely to occur over the segment of data for this channel, and the segment can also have a checksum for integrity checking and further identification. The transmitter and receiver can use fixed tables of channel sequences, so that once synchronized they can maintain communication by following the table. On each channel segment, the transmitter can send its current location in the table.
In the US, on unlicensed spread spectrum systems in the 902–928 MHz and 2.4 GHz bands permits more power than is allowed for non-spread-spectrum systems. Both frequency hopping and direct sequence systems can transmit at 1 Watt, a thousand-fold increase from the 1 milliwatt limit on non-spread-spectrum systems. The (FCC) also prescribes a minimum number of channels and a maximum dwell time for each channel.
In a real multipoint spread spectrum radio system, space allows the possibility of multiple transmissions on the same frequency using multiple radios in a geographic area. This creates the possibility of system data rates that are higher than the for a single channel. Spread spectrum systems do not violate the Shannon limit. Spread spectrum systems rely on excess signal to noise ratios for sharing of spectrum. This property is also seen in and systems. and directional antennas also facilitate increased system performance by providing isolation between remote radios.
Multiple inventors
In 1899 experimented with frequency-selective reception in an attempt to minimise interference.
The earliest mentions of frequency hopping in the open literature are in US patent 725,605 awarded to in March 17, 1903 and in radio pioneer ‘s book Wireless Telegraphy (German, 1908, English translation McGraw Hill, 1915), although Zenneck himself states that had already tried it. Nikola Tesla doesn’t mention the phrase “frequency hopping” directly, but certainly alludes to it. Entitled Method of Signaling, the patent describes a system that would enable radio communication without any danger of the signals or messages begin disturbed, intercepted, interfered with in any way .
The German military made limited use of frequency hopping for communication between fixed command points in to prevent eavesdropping by British forces, who did not have the technology to follow the sequence.
A engineer and inventor, , came up with the idea in 1929. Several other patents were taken out in the 1930s, including one by Willem Broertjes (, issued Aug. 2, 1932).
During , the was inventing a communication system called , which incorporated spread spectrum in a single frequency context. However, SIGSALY was a top-secret communications system, so its existence did not become known until the 1980s.
The most celebrated use of frequency hopping was a patent awarded to actress and composer , who in 1942 received for their “Secret Communications System”. This intended early version of frequency hopping was supposed to use a to change among 88 frequencies, and was intended to make radio-guided harder for enemies to detect or to jam, but there is no record of a working device ever being produced. The patent was rediscovered in the 1950s during patent searches when private companies independently developed , a non-frequency-hopping form of spread-spectrum, and has been cited numerous times since.
A practical application of frequency hopping was developed by , co-founder of Micrel Corporation. Zinn developed a method allowing radio devices to operate without the need to synchronize a receiver with a transmitter. Using frequency hopping and sweep modes, Zinn’s method is primarily applied in low data rate wireless applications such as utility metering, machine and equipment monitoring and metering, and remote control. In 2006 Zinn received for his “Wireless device and method using frequency hopping and sweep modes.”
Variations of FHSS
Adaptive Frequency-hopping spread spectrum (AFH) (as used in ) improves resistance to by avoiding crowded frequencies in the hopping sequence. This sort of adaptive transmission is easier to implement with FHSS than with .
The key idea behind AFH is to use only the “good” frequencies, by avoiding the “bad” frequency channels—perhaps those “bad” frequency channels are experiencing , or perhaps some third party is trying to communicate on those bands, or perhaps those bands are being actively jammed. Therefore, AFH should be complemented by a mechanism for detecting good/bad channels.
However, if the radio frequency interference is itself dynamic, then the strategy of “bad channel removal”, applied in AFH might not work well. For example, if there are several colocated frequency-hopping networks (as Bluetooth ), then they are mutually interfering and the strategy of AFH fails to avoid this interference.
The problem of dynamic interference, gradual reduction of available hopping channels and backward compatibility with legacy bluetooth devices was resolved in version 1.2 of the Bluetooth Standard (2003). Other Strategies for dynamic adaptation of the frequency hopping pattern have been reported in the literature. Such a situation can often happen in the scenarios that use .
In addition, dynamic radio frequency interference is expected to occur in the scenarios related to , where the networks and the devices should exhibit operation.
can be seen as a form of frequency-hopping that simply scans through the available frequencies in consecutive order to communicate.
Twitter
Telegram
